Links

menu path

QuickBar

"navigate to" links

Report center	= administrate report in the report center
driver administraion	= driver specific settings
settings order management	= settings of the order management

Actions

open help	= open the help for this topic
QuickLink	= creates a QuickLink for this page

On this page you are able to set up your firm specific settings of the timerecording.

The are 3 views for the configuration of transponder buttons available:

SBOX	the transponderreader in combination with the S-Box or the A-Box
NAVMAN MDT860	the Navman Display in combination with the A-Box or the C-Box
A1DLKP	the DriverLogKeyPad in combination with the A-Box

Enter here conceptualities of the respective bookings. Examples are besides the input field.

If nothing is entered, there are no more existing setting opportunities available!

Please enter here the naming of the time spans and sums. To have the entered values in the following steps of setting, just click on "Save".

timespan 1	: naming of timespan 1
timespan 2	: naming of timespan 2
day sum	: naming of the sum at the end of a day
total sum	: naming of the sum at the end of the report
sum of positive values to default work time	: naming for the poitive values of the difference to the default worktime
sum of negative values to default work time	: naming for the negative values of the difference to the default worktime
sum of difference to default worktime	: naming for sum of difference to the default worktime

The time report can be created between 2 time spans; a time span is the duration between 2 transponder actions.

timespan 1 begin	: action which should be use for the begin of timespan 1
timespan 1 end	: action which should be use for the end of timespan 1
timespan 2 begin	: action which should be use for the begin of timespan 2
timespan 2 end	: action which should be use for the end of timespan 2
which time span ist the break timespan	: which timespan should be use as break time
default breaktime mode	: You decide here in which way you want to use the default break time

don´t use default value	: No default breaktime will be used
default value takes effect always	: The given default breaktime will be used always (e.g.: booked breaktime 55 minutes, default 45 minutes --> breaktime: 45 minutes )
default value replaced non recorded break times	: For the case that no breaktime was booked, then the default break time will take effect (e.g.: booked breaktime 0 minutes, default 45 minutes --> breaktime: 45 minutes )
default value is minimal breaktime	: The given default breaktime is the minimum value (e.g.: booked breaktime 25 minutes, default 45 minutes --> breaktime: 45 minutes or booked breaktime 55 minutes, default 45 minutes --> breaktime: 55 minutes )

The day sum can be calculated by one or two time spans (e.g.: attendance - idletime).

mode selection:

timespan 1 + timespan 2
- example:
  - timespan 1: 4 hours
  - timespan 2: 2 hours
  - day sum: 6 hours
timespan 1 - timespan 2
- example:
  - timespan 1: 4 hours
  - timespan 2: 2 hours
  - day sum: 2 hours
timespan 2 - timespan 1
- example:
  - timespan 1: 4 hours
  - timespan 2: 4 hours
  - day sum: 0 hours
timespan 1
- example:
  - timespan 1: 4 hours
  - timespan 2: 2 hours
  - day sum: 4 hours
timespan 2
- example:
  - timespan 1: 4 hours
  - timespan 2: 2 hours
  - day sum: 2 hours

Settings of the report display.

activate default worktime calculation :	If a default worktime value is given, the value of the difference between the real and the default work time will be displayed. So a overtime calculation is possible.
show areas in reports :	Areas will be shown in the report. It will be displayed only these areas in which the car was at the time of booking and only from areas which are activated for that car to that time. ( more informations for alert monitoring )
show single recordings :	All recordings will be displayed.
show sum of recordings :	Day and total sums will be displayed. ( only in html view )

To send the settings to the accordings displays, navigate to the settings order management and send the settings to the displays.

Defualt work and break time will be defined in the drivers administration.