CommonAllows to define timerecording specific settings. Involves naming and linking of timeranges and calculation rules. Furthermore idle time regulations and report complexity can be set. | Info |
|---|
This setting is only available, if timerecording activated! |
BasicsIn general the timerecording module allows booking of two different time spans. Each timespan is framed by a start and end booking. It is possible to change labels for both timespan and booking activities here at any time. Changing the booking activity labels can be done at transponder button configuration. Depending on used device at the vehicle this labels can be seen directly on this device. For other devices you can see the assignment between labels and key names, selecting the according device via Mode. LinksQuickBar"navigate to" links Actions DescriptionOn this page you are able to set up your firm specific settings of the timerecording. The are 3 views for the configuration of transponder buttons available: SBOX | - the transponderreader in combination with the S-Box or the A-Box
| NAVMAN MDT860 | - the Navman Display in combination with the A-Box or the C-Box
| A1DLKP | - the DriverLogKeyPad in combination with the A-Box
|
Enter here conceptualities of the respective bookings. Examples are besides the input field. If nothing is entered, there are no more existing setting opportunities available! naming of the time spans and sumsPlease enter here the naming of the time spans and sums. To have the entered values in the following steps of setting, just click on "Save". The labels for timespans and sums are relevant for the timerecording report. The assignment of booking activities to the according timespans and the assignment, how to sum up the worktime can be done later via time calculation subpoint. To work with your own labels there, just click save settings after naming completed. time span 1 | label for timespan 1 | time span 2 | label for timespan 2 | worktime | timespan 1 | : naming of timespan 1 | timespan 2 | : naming of timespan 2 | day sum | : naming of the sum at the end of a day | total sumworktime | : naming of the sum at the end of the report | sum of positive values to default work time: naming for the poitive values of the difference to the default | if a default worktime is set and the person has a longer worktime | sum of negative values to default work time: naming for the negative values of the difference to the default worktime | if a default worktime is set and the worktime done by a person was shorter | sum of difference to default worktime: naming | label for sum of difference to the default the difference between a default worktime andmeasured worktime |
time calculationThe time report can be created between 2 time spans; a . A time span is the duration between 2 transponder actionsstart and end booking. timespan time span 1 begin | : action, which should be use used for the begin of timespan 1 | timespan time span 1 end | : action, which should be use used for the end of timespan 1 | timespan time span 2 begin | : action, which should be use used for the begin of timespan 2 | timespan time span 2 end | : action, which should be use used for the end of timespan 2 | which time span ist the break timespan | : which timespan should be use as break time | default breaktime mode | : You decide here in which way you want to use the default break time | don´t use default value | : No default breaktime will be usedallows assignment of one of the timespans as pause time | break time base | allows assignment of individual pause time for workdays | | breaktime offset type | if a base breaktime set, assign here, how to calculate this worktime for a workday; the calculation effect will be explained in next table |
This are the breaktime offset type calculation modes: default value takes effect always | : The given default breaktime will be used always (e.g.: booked breaktime 55 minutes, default 45 minutes --> breaktime: 45 minutes) | default value replaced non recorded break times | : For the case that no breaktime was booked, then the default break time will take effect (e.g.: booked breaktime 0 minutes, default 45 minutes --> breaktime: 45 minutes) | default value is minimal breaktime | : The given default breaktime is the minimum value (e.g.: booked breaktime 25 minutes, default 45 minutes --> breaktime: 45 minutes or booked breaktime 55 minutes, default 45 minutes --> breaktime: 55 minutes) | | default breaktime reduce day sum | No matter if a pause timespan was defined or a breaktime was booked, the default value will always used (e.g.: booked breaktime 25 minutes, default 45 minutes -> breaktime 70 minutes) |
calculation baseThe day sum worktime can be calculated by one or two time spans (e.g.: attendance - idletime).mode selection: Explanation of modes with some examples: + example:: timespan 2: day sum: | 6 hours | | timespan 1 - timespan 2 |
| 2 hours | | timespan 2 - timespan 1 |
If labels saved the timespan 1 and timespan 2 are directly named as defined via naming of the time spans and sums. report displaySettings of for the timerecording report display. activate default worktime calculation : | If a default worktime value is given, the value of the difference between the real and the default work time will be displayed. So a an overtime calculation is possible. | show areas cost centers in reports : | Areas will be shown in the report. It will be displayed only these areas in which the car was at the time of booking and only from areas which are activated for that car to that time. ( more informations for alert monitoring ) | show single recordings : | All recordings will be displayed. | show sum of recordings : | Day and total sums will be displayed. ( only in html view ) |
| If show detailed bookings enabled, show all cost centers active when a booking was done. Otherwhise for each day a list of cost centers will be visible, which were active at any booking. | show detailed bookings | If this option is selected, for each day a bookings graph is visible and a table with each single booking is shown. If it is disabled for each day just the calculated sums will be printed. | | show shift times | Extends the per day summaries of the HTML and PDF report by a shift start and -end time. While the start is similr to the start of the first booking at the current day, the end is marked by the end of the latest booking at the accodring calendaric day. |
To send the settings to the accordings displays, navigate to the settings order management settings and send the settings to the displays. define default timesDefualt work and break time will be defined in the drivers administration. back to Professional-Portal timerecording settingsThe default work and breaktimes will be saved per person and can be set at Administration -> Personnel management. For a report always the default values on report execution will be used. |