Common

The digitacho administration grants access and control for driver and vehicle filese, created by digital tachograph.

Download/Archive

Here are listed all available DDD files. If there is booked only the download functionality, the bold marked files still have to be archived by the user. Otherwhise no action is required and the mark just indicates if a file was eported earlier.

The visible files can be limited by setting a driver, a vehicle, an archive state or a timerange. Vehicles can be filtered by group, company card (used for download) and single vehicle. The company card filter only shows files, downloaded via selected company card (including according following cards). For drivers the filter options are by group, by place of employment or by a selected single driver. The place of employment will be set via personnel administration.

On open this page there will be visible all new files, not archived or exported by the user and downloaded from the tachograph during the 30 days. Changing the according input values will result in access to any files stored in the system.

Clicking a column headline will result in sorting the data by this column.

Changing the filter by option from download date to content timerange will result in a different file arrangement. In content mode for each vehicle or driver will be visible only one entry row. This row may consist of one or multiple files, to cover the desired timerange in an optimal arrangement with minimal overhead for start end end time. If it is impossible to get a set of files, covering the desired timerange, no entry will be made for this driver or vehicle!

Selecting a single file for download to the own computer will result in directly downloading this file. If multiple files selected for download a compressed .zip file will be created, containing all selected files.

Download states

For each driver and each vehicle, with DDD files available, the dates for latest download and deadline for next download is visible. For each entry also a check is done, if all data for the whole timerange is available at storage.

A limitation for drivers and vehicles cane be done on top of this tab.
Using the default setup, drivers or vehicles, without any DDD files will not be visible in table. To change this behaviour, select the show drivers/vehicles without downloads option.
For some special cases additionally the digitacho delivers data for drivers, not registered at personal administration. This unknown drivers are hidden by default, too. To show this personal, uncheck the hide unknown personal option.

The state column at data table consist of different available states:

Download state details

If at least one digitacho file ist stored for a driver or vehicle, a details page can be called. This details page shows a month calendar for a quick overview, which file is available for which calendaric day and at which days no data available.
A day, marked green indicates, that at least one file with data is available. Moving the cursor over this day, will result in a list of available files for this day.
A red marked day, indicates missing files for this day. This means, no file is available at storage, containing data for this day.

Download state incomplete data

The incomplete data state is a special state, that should not occur on normal operation. Although for each download a check will be done, which data are available and download a mostly complete data set, sometimes there are timeranges without any data at the storage. This may happen, if a vehicle will be repaired and the digital tachograph will get no power for longer timeranges, or there is any kind of malfunction.

The first step to handle this kind of error is downloading the data directly at the vehicle and adding this data to the storage. If the gaps will not be closed after this procedure, probably the digital tachograph has a malfunction and should be checked immediately.

Download state diable vehicle observation

If a vehicle is not part of the vehicle fleet anymore, an error message will be shown on exceeding the download time limit, too. To handle this, it is possible to mark the timerange after latest download as ignored timerange. So the vehicle will be still kept in list for archivation but will not be visible prominent anymore. If even the latest file exceeds the archivation timerange, the vehilce will be removed completely from list.

Drivers

The handling of this module is similar to the personal administration.
As limitation here only persons are shown, having a 16-char long driver key as personal key. Additionally the table columns can be configured independently to personal administration.

Omitted reasons

To match the regularities of european drivers edict a driver has to verify his activities for the last 28 days. While driving activities registered by digital tachograph, in case of other activities, illness or spare time the driver has to show documents for this activities. This document is called "attestation of activities".

This menu allows to create those documents and check, if this documents where generated completely.
Therefore the overview tab shows the list of all drivers and checks all states for the last 28 days. This check can result in 3 different state messages:

1. could not determine the state: no digitacho data for the last 28 days found
2. no gaps found in timerange: all documents where created for the timerange
3. data incomplete: digitacho data found but missing activities documents for at least one day

To get detailed information, especially why an incomplete state was set, for each driver exist the action to open a detailed view. This view is equal to omitted reason details with current driver preselected.

After this page is called, the calculation of state message will be startet. The current calculation state and the according results stay in memory, as long as the archive management module is active. To refresh the driver data, just use the reload funtion on top of this tab or restart the archive management module.

Selecting one driver, show the according detailed booking data and documents.

Omitted reasons per driver

On top of this tab are the buttons to reload, enter an other activity and to switch between tabellaric ond graphic bookings view. If the tab was direcly selected, first chose the driver, if called from omitted reason overview list, a driver is preselected.

After a driver is selected, the data for current and previous month will be loaded to show the timerange of last 28 days without any scrolling or paging. The days itself are marked as follows:

Mark	Meaning
Image Added	No data available for this day.
Image Added	Bookings found for this day and no other activities document required.
Image Added	For this day a document should be added.

Klicking on any day of the calendar will also refresh the 3-days-view below this calendar. To improve the readability, the previous and next day also will be visible.

If no data available for a timespan or if a timespan is marked as idle timespan, a new other activity document can be created, just by clicking on this timerange at graphic or by click on the according action in tabellaric mode.
In this case only the reason has to be set and all other values are prefilled.

Especially in the very first usage, probably not all informations are stored for each driver. Because this data are required to create the document, it is possible to fill the missing data directly in this input mask. The data entered here will also be stored to database, so they did not have to be entered multiple times.
This personal informations are the drivers birthdate, the driver is employee since date and an identification document. This identification document may be the driver licence, identy card or passport. Becaue this documents have a limited validity, it's recommended to add the valid to date.

The document also contains data about the creator. This is the name, position in the company and the address. Creator is the currently logged in user. If no specific address is set, the global company address will be used. The position and a differing working address can be set at Adminitration -> Portal Settings -> Settings / User data.

To handle weekends easier, it is also possible to create activity documents for multiple drivers in one step. To do so, use second option in driver selection (select multiple drivers). This will result in a list of all drivers with a checkbox for each driver to select the ones, that need a document. In this mode it is not possible to append missing personal data to any of the drivers, so if data missing for any driver, a remark text will be shown and this driver is not visible in the main list.
To check, for which drivers data missing, there can be expanded a second list, just with the name of all drivers with incomplete data.

To not reopen the input mask for different timeranges, just change the option for save button to only save and print. Closing the input mask is possible via aborting further inptu or just clicking X on the bottom ricght.

If such an other activity was entered, in graphic mode this timerange is marked by a blue line. In tabellaric mode the entry is marked bold and has its own icon for faster identification.

Clicking on such an entry will allow to reprint the document, change the data or delete it.

Branch offices

If the company consist of multiple branch offices, so the according disponent can set its specific branch address via Einstellungen / Nutzerdaten. Here the correct branch office address can be stored.

Violations

The violation overview is a brief indicator if there are any violations for a driver and how to rate this violations.

The initial selection calculates all violations for the current and previous month. Including the count of violations and possible cost as defined in schedule of fines. Additionally is the violation infringement as defined in EU regulation 2016/403. Depending on count and infringement type there is an area of discretion for the BAG. Additionally usage faults of the tachograph may be respected so the real value may differ from this precalculation.

Values for already printed violations and newly calcultated ones will be shown separate.

Levels of infringement

violations per driver

Using the detailed view for a driver allows to anlyse each single violation.
For the selected driver a month overview is visible. This month overview is colored to indicate the state per calendaric day. Therefore the following colors are used:

Moving the mouse over a red marked day, will also mark the according violation entries in the violations table below the calendar red.

This table shows base data for each violation in visible time range. For each violation the infringement level and possible cost shown. If the user added real costs for a violation, these costs will be visible instead of common value.

To get even more details for a violation, use the details button. For timeranges up to 2 days, a graph will be shown with each single activity bookings and the range with the violation is marked blue. For longer violations the relevant data will be visible in a table.

Similar to violations overview it is possible to select violations to print an instruction.

Violation prints

Printing the instruction protocol is available from violations overview and violation details tab. 
Printing from overview always only creates an instruction for new violations, not printed before and not marked with a penalty fee of 0,- €.
From violation details tab it is possible to make an own combination or just to reprint an instruction. If an instruction selected, which was printed before, the according instruction protocol will be printed same as ist was printed initially. This means with all other according violations, also printed on the page. In combination with never printed violations, the not printed violations will be printed to an extra page. So it is possible to create copies of the original instructions at any time. Aditionally the signing information has to be entered just for one violation of the page.

The document itself contains informations about timerange, allowance and effective value (idle time, driving time, ...). Additionally the type of violation and the according link to legal text is shown.

Bookings

Overview

The bookings overview allows to check and analyze the steer- and worktimes for drivers with digitacho data. After selecting a driver, a table with steer-, work-, and standby times of the last month will be displayed.

After first loading, above the table is a toggle switch to differ between a calendaric-day based view and a shift-day based view.

The shift-day view is intened to help understanding possible violations. Thats why shift-weeks will be shown completely always, even if only 1 shift day is part of requested time range.

A calendaric day in general starts at 00:00 UTC and ends 24:00 UTC. A calendaric week always starts at monday 00:00 UTC and ends on sunday 24:00 UTC.

To get a report with splitting at local time and/or shifts, cropped at report range, you can use the tacho-work-times report.

The times can be translated into local time via general settings.

Detailed view

This detailed view is divided into 2 modes, too. By default a table with all single bookings is shown.There is an additional tab to switch to a graphical view. Here a bar visualizes the times for each day. The meaning of the marked timeranges is similar to the omitted reasons tab.

There is an export funktion available at each tab. This function will export the currently visible data to a PDF, Excel or CSV file. The file content depends on currently visible data.

Uploads

If driver or vehicle data are incomplete or just shall be added to the archive, they can be uploaded to the archive here.

The files to add must be of filetype .ddd. Generally the filename has following scheme:

To add a file to the archive, click the upload button (Image Added) to open the file selection dialog to select one or multiple files. The menu also supports dragging the files just over the table to initialize the upload. The upload itself starts immediately for up to 200 files at once. Each uploaded file has to pass a validity check, once it is completely transferred to the server. If this check fails, there will be returned an error message for the file and it will not be stored permanently in the archive!

To get the filestates there is an extra menu on the left side above the self created quicklink list. This extra menu initially only shows the overall progress. On click there will be opened a more detailled view with all files and theyr current upload state.

If a file was uploaded successfully, the according success state will remain 10 minutes in list before the list will be cleaned. If there was an error, the file with according error message remains 30 minutes in the list.

Once an upload is initialized, it is possible to go on working with the portal. The uploads will be handled in background. A complete page reload as done by pressing <F5> key will abort further processing!

Vehicle Events

This views shows all events stored in vehicle units between current day and the previous three months. The time range may consist up to 2 years.

To allow an easier handling for large vehicle fleets the check up can be limited to selected vehicles and vehicle groups.

The analysis result is divided into 8 categories:

Selecting one of the categories opens the list with all according events. For each of this events a detailed view is available to show additional information for the selected event and all other events within a 12 hour time range.

Each event can be marked as noticed, too. Such a noticed events won't be listed in the overview list anymore. Using the checkboxes, multiple events can be noticed in one step. Hereby the portal user's name and the time always will be stored. Optional an additional remark text can be added.

Vehicle Activities

This tab is mostly similar to the existing bookings list but the bookings will be extracted from vehicle files instead of driver files.

So the most obvious change ist the division into both tacho slots and independent calculation. Besides this the most important change is the different calendaric day calculation, if local time selected. In contrast to the rest of the digitacho archive the day change in local time will be done at 00:00 local time instead of using the UTC base.

There is an optional column "odometer UTC day". Because of available data, this odometer states always refer to 00:00 - 24:00 of the UTC based day, so this may result in differencies if there is an overnight drive. For each day the first and last odometer state is shown, the summaries show the driven distance in km for the according time range.

Just as realized in the booking list the visible columns of the overview can be changed and the exported files depend on the current column setting. In detailed view the exported files always contain data for both slots.

The maximum timerange to analyze here may cover 3 months, too.

Digitacho odometer report

Common

This module shows odometer states based on mass storage data. The selected daterange always starts at 00:00 of the day and ends at midnight. So selecting the same start and end date will return per-day distance.

To filter the resulting list, the group, company-card and vehicle selctions are available.

Export

The result list can be exported as PDF or Excel file.

Settings

This tab joins all setting options according to the digitacho module.

Common Settings

The first Setting allows to set the default table rows for all list views. Changing the row count directly in the module will only keep this setting, during the session. By starting a new session the row count will be set to the value in this menu. For further Archive functions the visible time base can be modified here. By EU regularities the calculation base is UTC time. To allow an easier check of calculated times and dates, the visible times can be recalculated to ME(S)Z timezone. This change only affects the portal output!

Setup tabs

To match different requirements the visible tabs and their order can be set here.

Drivers table

Allows to set the visible columns and their order for the drivers table

Other activities

In general an other activities document will be printed in current portal language. This language can be changed for each single print. Alternatively a different default language can be set here. This may be helpful especially if the vehicles mostly active in foreign countries.

The next option is to set the duration of an unknown span to be classified as warning. By law a gap-less logging of all activities is required. In general short gaps won't be chased as a violation, if the booked times still allow a comprehensible control.

According to EG regularities 3821/85 article 15 paragraph 2 a document for "other activities" has to be created and issued to the driver before he starts it's drive. So its possible reject creation of documents in the past. In contrast to this regularities it's helpful to have a documentation even in this cases.

Violation settings

This submenu allows to change the settings for violation recognition and print views.

Warnings

Here you can automatically check some tachopgraph specific time limits and let create a warn message or email if required. This check is available for the following options:

For each warn profile multiple recipients can be set, where each entry has its own prewarn duration. So it's possible to have a single portal warning one month before the tacho-check expires and then get an email every day, if the required check date is in less than a week.

Archive period

Depending on company country and archive usage the resulting lawful archiving rules differ. The usage type can be set here.

The european common archive duration is one year and the files shall be deleted at next march.

Despite this european regulation there are different archive times, if this bookings will be used for work time calculation.

Timerecording

If timerecording is activate, the booked driver data can modified to regular timerecording bookings automatically. The converted content differs by timerecording settings and settings in this dialog.

If you are using the current timerecording module the booked activities will be exported directly.

If you are using the old timerecording module, the bookings have to be translated into old booking mode, which means all bookings except a break are assigned to work time and if project time span is available, steer and standby state will be added as named project time. If a break span is defined, the idle times less than 7 hours will be assigned as break, too.

Company cards

In addition to regular vehicle groups, there is an option to filter vehicles by company card, used for download. This allows filtering by different branches without creating and managing vehicle groups.

This menu is to add a name and address for each branch of the company.

A company card itself has a 16-digit number. The first 13 digits are used to identify the company itself. The last 3 digits are reserved for the according following card numbers. Thats why the number is dividied into this 13+3 digit prompt.

It is possible to add new base cards with the complete 13 + 3 digit number or just add following cards by entering the last 3 digits. Each following card may have its own validity. Adding a validity is recommended to see the latest validity end directly at overview page,

Similar to search for new transponders at personnel administration, there is a search for unknown company cards, too. This search is based on processed mass storage data and already adds the company name as defined on card. But this means, the mass storage data have to be analyzed first, which means there is a gap of up to 24 hours between upload and availabity of company card data

Common

The digitacho administration grants access and control for driver and vehicle filese, created by digital tachograph.

Download/Archive

Here are listed all available DDD files. If there is booked only the download functionality, the bold marked files still have to be archived by the user. Otherwhise no action is required and the mark just indicates if a file was eported earlier.

The visible files can be limited by setting a driver, a vehicle, an archive state or a timerange.

On open this page there will be visible all new files, not archived or exported by the user and downloaded from the tachograph during the 30 days. Changing the according input values will result in access to any files stored in the system.

Clicking a column headline will result in sorting the data by this column.

Changing the filter by option from download date to content timerange will result in a different file arrangement. In content mode for each vehicle or driver will be visible only one entry row. This row may consist of one or multiple files, to cover the desired timerange in an optimal arrangement with minimal overhead for start end end time. If it is impossible to get a set of files, covering the desired timerange, no entry will be made for this driver or vehicle!

Selecting a single file for download to the own computer will result in directly downloading this file. If multiple files selected for download a compressed .zip file will be created, containing all selected files.

Download states

For each driver and each vehicle, with DDD files available, the dates for latest download and deadline for next download is visible. For each entry also a check is done, if all data for the whole timerange is available at storage.

A limitation for drivers and vehicles cane be done on top of this tab.
Using the default setup, drivers or vehicles, without any DDD files will not be visible in table. To change this behaviour, select the show drivers/vehicles without downloads option.
For some special cases additionally the digitacho delivers data for drivers, not registered at personal administration. This unknown drivers are hidden by default, too. To show this personal, uncheck the hide unknown personal option.

The state column at data table consist of different available states:

Download state details

If at least one digitacho file ist stored for a driver or vehicle, a details page can be called. This details page shows a month calendar for a quick overview, which file is available for which calendaric day and at which days no data available.
A day, marked green indicates, that at least one file with data is available. Moving the cursor over this day, will result in a list of available files for this day.
A red marked day, indicates missing files for this day. This means, no file is available at storage, containing data for this day.

Download state incomplete data

The incomplete data state is a special state, that should not occur on normal operation. Although for each download a check will be done, which data are available and download a mostly complete data set, sometimes there are timeranges without any data at the storage. This may happen, if a vehicle will be repaired and the digital tachograph will get no power for longer timeranges, or there is any kind of malfunction.

The first step to handle this kind of error is downloading the data directly at the vehicle and adding this data to the storage. If the gaps will not be closed after this procedure, probably the digital tachograph has a malfunction and should be checked immediately.

Download state diable vehicle observation

If a vehicle is not part of the vehicle fleet anymore, an error message will be shown on exceeding the download time limit, too. To handle this, it is possible to mark the timerange after latest download as ignored timerange. So the vehicle will be still kept in list for archivation but will not be visible prominent anymore. If even the latest file exceeds the archivation timerange, the vehilce will be removed completely from list.

Drivers

The handling of this module is similar to the personal administration.
As limitation here only persons are shown, having a 16-char long driver key as personal key. Additionally the table columns can be configured independently to personal administration.

Omitted reasons

To match the regularities of european drivers edict a driver has to verify his activities for the last 28 days. While driving activities registered by digital tachograph, in case of other activities, illness or spare time the driver has to show documents for this activities. This document is called "attestation of activities".

This menu allows to create those documents and check, if this documents where generated completely.
Therefore the overview tab shows the list of all drivers and checks all states for the last 28 days. This check can result in 3 different state messages:

1. could not determine the state: no digitacho data for the last 28 days found
2. no gaps found in timerange: all documents where created for the timerange
3. data incomplete: digitacho data found but missing activities documents for at least one day

To get detailed information, especially why an incomplete state was set, for each driver exist the action to open a detailed view. This view is equal to omitted reason details with current driver preselected.

After this page is called, the calculation of state message will be startet. The current calculation state and the according results stay in memory, as long as the archive management module is active. To refresh the driver data, just use the reload funtion on top of this tab or restart the archive management module.

Selecting one driver, show the according detailed booking data and documents.

Omitted reasons per driver

On top of this tab are the buttons to reload, enter an other activity and to switch between tabellaric ond graphic bookings view. If the tab was direcly selected, first chose the driver, if called from omitted reason overview list, a driver is preselected.

After a driver is selected, the data for current and previous month will be loaded to show the timerange of last 28 days without any scrolling or paging. The days itself are marked as follows:

Mark	Meaning
Image Removed	No data available for this day.
Image Removed	Bookings found for this day and no other activities document required.
Image Removed	For this day a document should be added.

Klicking on any day of the calendar will also refresh the 3-days-view below this calendar. To improve the readability, the previous and next day also will be visible.

If no data available for a timespan or if a timespan is marked as idle timespan, a new other activity document can be created, just by clicking on this timerange at graphic or by click on the according action in tabellaric mode.
In this case only the reason has to be set and all other values are prefilled.

Especially in the very first usage, probably not all informations are stored for each driver. Because this data are required to create the document, it is possible to fill the missing data directly in this input mask. The data entered here will also be stored to database, so they did not have to be entered multiple times.
This personal informations are the drivers birthdate, the driver is employee since date and an identification document. This identification document may be the driver licence, identy card or passport. Becaue this documents have a limited validity, it's recommended to add the valid to date.

The document also contains data about the creator. This is the name, position in the company and the address. Creator is the currently logged in user. If no specific address is set, the global company address will be used. The position and a differing working address can be set at Adminitration -> Portal Settings -> Settings / User data.

To handle weekends easier, it is also possible to create activity documents for multiple drivers in one step. To do so, use second option in driver selection (select multiple drivers). This will result in a list of all drivers with a checkbox for each driver to select the ones, that need a document. In this mode it is not possible to append missing personal data to any of the drivers, so if data missing for any driver, a remark text will be shown and this driver is not visible in the main list.
To check, for which drivers data missing, there can be expanded a second list, just with the name of all drivers with incomplete data.

To not reopen the input mask for different timeranges, just change the option for save button to only save and print. Closing the input mask is possible via aborting further inptu or just clicking X on the bottom ricght.

If such an other activity was entered, in graphic mode this timerange is marked by a blue line. In tabellaric mode the entry is marked bold and has its own icon for faster identification.

Clicking on such an entry will allow to reprint the document, change the data or delete it.

Violations

Another main feature of file analysation is the calculation of violations against drivers regulation. The calculation is only based on DDD files data. Data from digitacho live view interface will be ingored here.
For the table all new violations from start of previous month will be calculated. Already printed violations will be ignored. In the table is just the penalty fee visible, caused by the calculated violations.
Because the schedule of fines just contains the standard values, only this will be used for calculation. The controlling officers may raise or decrease the single penalty fees in some cases. So the calculated penalty fee is just an indicator, which costs have to be expected.

Similar to omitted reasons overview it is possible to open a more detailed view for a single driver.

violations per driver

Using the detailed view for a driver allows to anlyse each single violation.
For the selected driver a month overview is visible. This month overview is colored to indicate the state per calendaric day. Therefore the following colors are used:

Moving the mouse over a red marked day, will also mark the according violation entries in the violations table below the calendar red.

This table shows more detailed data for each single violations at active month. Additionally vor each violation the calculated penalty fee is shown. If a driver was controlled a real payed penalty can be entered. If such a real payment was entered, this payment will be shown instead of assumed calculation.

To get even more details for a violation, use the details button. For timeranges up to 2 days, a graph will be shown with each single activity bookings and the range with the violation is marked blue. For longer violations the relevant data will be visible in a table.

Similar to violations overview it is possible to select violations to print an instruction.

Violation prints

Printing the instruction protocol is available from violations overview and violation details tab. 
Printing from overview always only creates an instruction for new violations, not printed before and not marked with a penalty fee of 0,- €.
From violation details tab it is possible to make an own combination or just to reprint an instruction. If an instruction selected, which was printed before, the according instruction protocol will be printed same as ist was printed initially. This means with all other according violations, also printed on the page. In combination with never printed violations, the not printed violations will be printed to an extra page. So it is possible to create copies of the original instructions at any time. Aditionally the signing information has to be entered just for one violation of the page.

The document itself contains informations about timerange, allowance and effective value (idle time, driving time, ...). Additionally the type of violation and the according link to legal text is shown.

Bookings

The bookings overview allows to check and analyze the steer- and worktimes for drivers with digitacho data. After selecting a driver, a table with steer-, work-, and standby times of the last month will be displayed. By pressing the button to toggle the view mode Image Removed, it is possible to switch to a shift worktime based view. This view complies with the doubleweek report. For each timerange of the calendaric table (day, week, overall) is a detailed view button.

This detailed view is divided into 2 modes, too. By default a table with all single bookings is shown.There is an additional tab to switch to a graphical view. Here a bar visualizes the times for each day. The meaning of the marked timeranges is similar to the omitted reasons tab.

There is an export funktion available at each tab. This function will export the currently visible data to a PDF, Excel or CSV file. The file content depends on currently visible data.

Uploads

If driver or vehicle data are incomplete or just shall be added to the archive, they can be uploaded to the archive here.

The files to add must be of filetype .ddd. Generally the filename has following scheme:

To add a file to the archive, click the upload button (Image Removed) to open the file selection dialog to select one or multiple files. The menu also supports dragging the files just over the table to initialize the upload. The upload itself starts immediately for up to 200 files at once. Each uploaded file has to pass a validity check, once it is completely transferred to the server. If this check fails, there will be returned an error message for the file and it will not be stored permanently in the archive!

To get the filestates there is an extra menu on the left side above the self created quicklink list. This extra menu initially only shows the overall progress. On click there will be opened a more detailled view with all files and theyr current upload state.

If a file was uploaded successfully, the according success state will remain 10 minutes in list before the list will be cleaned. If there was an error, the file with according error message remains 30 minutes in the list.

Once an upload is initialized, it is possible to go on working with the portal. The uploads will be handled in background. A complete page reload as done by pressing <F5> key will abort further processing!

Vehicle Events

This views shows all events stored in vehicle units between current day and the previous three months. The time range may consist up to 2 years.

To allow an easier handling for large vehicle fleets the check up can be limited to selected vehicles and vehicle groups.

The analysis result is divided into 5 categories:

Selecting one of the categories opens the list with all according events. For each of this events a detailed view is available to show additional information for the selected event and all other events within a 12 hour time range.

Each event can be marked as noticed, too. Such a noticed events won't be listed in the overview list anymore. Using the checkboxes, multiple events can be noticed in one step. Hereby the portal user's name and the time always will be stored. Optional an additional remark text can be added.

Vehicle Activities

This tab is mostly similar to the existing bookings list but the bookings will be extracted from vehicle files instead of driver files.

So the most obvious change ist the division into both tacho slots and independent calculation. Besides this the most important change is the different calendaric day calculation, if local time selected. In contrast to the rest of the digitacho archive the day change in local time will be done at 00:00 local time instead of using the UTC base.

Just as realized in the booking list the visible columns of the overview can be changed and the exported files depend on the current column setting. In detailed view the exported files always contain data for both slots.

The maximum timerange to analyze here may cover 3 months, too.

Settings

This tab joins all setting options according to the digitacho module.

Common Settings

The first Setting allows to set the default table rows for all list views. Changing the row count directly in the module will only keep this setting, during the session. By starting a new session the row count will be set to the value in this menu. For further Archive functions the visible time base can be modified here. By EU regularities the calculation base is UTC time. To allow an easier check of calculated times and dates, the visible times can be recalculated to ME(S)Z timezone. This change only affects the portal output!

Setup tabs

To match different requirements the visible tabs and their order can be set here.

Drivers table

Allows to set the visible columns and their order for the drivers table

Other activities

In general an other activities document will be printed in current portal language. This language can be changed for each single print. Alternatively a different default language can be set here. This may be helpful especially if the vehicles mostly active in foreign countries.

Violation settings

Violation calculation and resulting instruction protocols specific settings can be done here. The meaning of the different settings is also explained behind each of the settings.

Warnings

Setting a valid to date for any identification document of a driver, allows to check the expiration dates automatically with this module. Therefore a nightly check will be executed to proove, if any data for a configured driver exceeding a predefined limit. If so, a portal message or an email will be created to inform about soon expiration.

The default view shows the list with already created profiles and for each profile the observed drivers and personal groups and the assigned recipients for the warn messages.

On create a new warn profile or edit an existing one an input mask will be opened. Here you can set the checked document types, the persons and personal groups and the according recipients with their prewarn times. The prewarn time is recipient specific to allow multiple message to one recipient with differing prewarn times or multiple recipients. So you can warn the disponent with "regular" prewarn times and also sent an extra message, if even days before an expiration no new document data available. Portal and email messages can be mixed without any limitation.

Archive period

Depending on archive usage the resulting lawful archiving rules differ.The usage type can be set here.

Timerecording

If timerecording is activate, the booked driver data can modified to regular timerecording bookings automatically. The converted content differs by timerecording settings and settings in this dialog.

The timespans work, standby and steering always will be assigned as worktime. Additional steering and standby times can be marked as project times to ensure diffentiated accounting of different timespans. The option to differentiate is only available, if project time is activated.

Additional to work time, the idle timespans can be shown. This requires a defined pause timespan in timerecording configuration. To check correct setup, the currently detected configuration is shown in this dialog. If a pause timespan is set, all idle times not exceeding a 7 hour timerange will be marked as pause time.

Legend

	Mark a ddd file with vehicle specific data.
	Mark a ddd file with driver specific data.
	Opens the details for accoding entry.
	Loads the file for this driver or vehicle (if multiple files in the row, download as zip archive).
	Loads the files for checked drivers and vehicles (if multiple entries selected, download as zip archive).
	Create a new other activities document.
	Toggle between tabellaric and graphic view of bookings.
	If the detailed view for a driver at omitted days or violations is selected, this will send you back to the overview list.
	Create a PDF document with instructions for selected violations.
	Open the dialog to upload one or multiple files.